Who Killed Adam Radford In Absentia, Articles C

A51 For aircraft batteries, irrespective of the quantity limitations specified in Column (9A) of the 172.101 Table or 175.75(c), wet cell batteries, UN2794 or UN2795, up to a limit of 100 kg net mass per package may be transported aboard passenger aircraft. 421 This entry will no longer be effective on January 2, 2023, unless we terminate it earlier or extend it beyond that date by notice of a final rule in the Federal Register. The consignor shall be in possession of a copy of each applicable certificate when packages include fissile material excepted by competent authority approval. B134 For Large Packagings offered for transport by vessel, flexible or fibre inner packagings shall be sift-proof and water-resistant or shall be fitted with a sift-proof and water-resistant liner. 55 This device must be approved in accordance with 173.56 of this subchapter by the Associate Administrator. 1 CFR 1.1 (i) These provisions apply to the transportation of hazardous materials in IM and UN Specification portable tanks. The temperature of the material at the time it is offered for transport and during transportation may not exceed 55 C (130 F). Table 1 authorizes IBCs for specific proper shipping names through the use of IB Codes assigned in the 172.101 table of this subchapter. N87 The use of copper valves on UN pressure receptacles is prohibited. 48 Mixtures of solids that are not subject to this subchapter and toxic liquids may be transported under this entry without first applying the classification criteria of Division 6.1, provided there is no free liquid visible at the time the material is loaded or at the time the packaging or transport unit is closed. 345 Nitrogen, refrigerated liquid (cryogenic liquid), UN1977 transported in open cryogenic receptacles with a maximum capacity of 1 L are not subject to the requirements of this subchapter. IBCs of type 31A and 31N are only authorized if approved by the Associate Administrator. For a battery whose voltage (electrical potential) exceeds 9 volts -, (1) When contained in a device, the device must be packaged in a manner that prevents unintentional activation or must have an independent means of preventing unintentional activation (e.g., packaging restricts access to activation switch, switch caps or locks, recessed switches, trigger locks, temperature sensitive circuit breakers, etc. A5 Solids having an inhalation toxicity of Packing Group I are not permitted on passenger aircraft and may not exceed a maximum net quantity per package of 15 kg (33 pounds) on cargo aircraft. This includes hybrid electric vehicles powered by a fuel cell, an internal combustion engine, and wet, sodium or lithium batteries installed. The Associate Administrator may except from the requirements of this subchapter articles, machinery, and apparatus provided: a. b. 336 The use of UN1H1 drums, UN3H1 jerricans, and UN6HA1 composite packagings which meet the requirements of part 178 of the HMR at the Packing Group I or II performance level. The set to discharge for the spring loaded pressure relief device and the burst pressure for the frangible disc, as applicable, must not be greater than 2.65 bar for portable tanks with minimum test pressures greater than 4 bar; b. TP24 The portable tank may be fitted with a device to prevent the build up of excess pressure due to the slow decomposition of the hazardous material being transported. This training must be documented in training records required by 172.704(d). b. 353 Ammonium permanganate, ammonium permanganate aqueous solutions, and mixtures of a permanganate with an ammonium salt are forbidden for transport. c. The time between offering the material for transportation at the point of origin, and unloading the material at the destination does not exceed 48 hours. 130 Batteries, dry, sealed, n.o.s., commonly referred to as dry batteries, are hermetically sealed and generally utilize metals (other than lead) and/or carbon as electrodes. subject to the Hazardous Materials Regulations must comply with all applicable requirements of Subpart F [172.500]. 386 When transported by private motor carrier only, the following corrosive liquids may be packaged in polyethylene bottles with a capacity no greater than 3.785 L (one gallon), further packed inside an open-top, heavy wall, high density polyethylene box (i.e., crate) in a manner that the polyethylene bottles are not subjected to any superimposed weight, and the boxes must be reasonably secured against shifting within the transport vehicle and loaded so as to minimize the possibility of coming in contact with other lading: Compounds, cleaning liquid, NA1760, PG II or III; Corrosive liquid, acidic, inorganic, n.o.s., UN3264, PG II; Corrosive liquid, acidic, organic, n.o.s., UN3265, PG III; Corrosive liquid, basic, inorganic, n.o.s., UN3266, PG II; Hydrochloric acid solution, UN1789, PG II; and. Packagings must be sift-proof, prevent liquid water from reaching the hazardous material, and be provided with sufficient venting to preclude dangerous accumulation of flammable, corrosive, or toxic gaseous emissions such as methane, hydrogen, and ammonia. Except for a portable tank containing refrigerated liquefied helium, a portable tank shall have an outage of at least two percent below the inlet of the pressure relief device or pressure control valve, under conditions of incipient opening, with the portable tank in a level attitude. A101 In addition to the applicable requirements of 173.185, the quantity of lithium metal in the batteries contained in any piece of equipment must not exceed 12 g per cell and 500 g per battery. Flammable components are flammable liquids and liquid mixtures, flammable solids and solid mixtures or flammable gases and gas mixtures meeting the following criteria: (1) A flammable liquid is a liquid having a flashpoint of not more than 93 C (200 F); (2) A flammable solid is a solid that meets the criteria in 173.124 of this subchapter; or. The total weight of the explosive contents of the shaped charges assembled in the guns does not exceed 90.5 kg (200 pounds) per vehicle; and. B115 Rail cars, highway trailers, roll-on/roll-off bins, or other non-specification bulk packagings are authorized. (h) Column 7: Special provisions. 138 This entry applies to lead compounds which, when mixed in a ratio of 1:1,000 with 0.07 M (Molar concentration) hydrochloric acid and stirred for one hour at a temperature of 23 C 2 C, exhibit a solubility of more than 5%. b. The manufacturer must apply procedures to ensure that articles produced in series are made of good quality, conform to the design type and are able to meet the requirements in (a). 53 Packages of these materials must bear the subsidiary risk label, EXPLOSIVE, and the subsidiary hazard class/division must be entered in parentheses immediately following the primary hazard class in the shipping description, unless otherwise provided in this subchapter or through an approval issued by the Associate Administrator, or the competent authority of the country of origin. 335 Mixtures of solids that are not subject to this subchapter and environmentally hazardous liquids or solids may be classified as Environmentally hazardous substances, solid, n.o.s, UN3077 and may be transported under this entry, provided there is no free liquid visible at the time the material is loaded or at the time the packaging or transport unit is closed. When a specific portable tank instruction is specified by a T Code in Column (7) of the 172.101 Table for a specific hazardous material, a specification portable tank conforming to an alternative tank instruction may be used if: (A) The alternative portable tank has a higher or equivalent test pressure (for example, 4 bar when 2.65 bar is specified); (B) The alternative portable tank has greater or equivalent wall thickness (for example, 10 mm when 6 mm is specified); (C) The alternative portable tank has a pressure relief device as specified in the T Code. "Published Edition". N8 Nitroglycerin solution in alcohol may be transported under this entry only when the solution is packed in metal cans of not more than 1 L capacity each, overpacked in a wooden box containing not more than 5 L. Metal cans must be completely surrounded with absorbent cushioning material. The material may only be loaded with Class 3, Class 8, and Division 4.1 materials in Packing Group II or III. citations and headings For non-pressurized lighters containing a Class 3 (flammable liquid) material, its design, description, and packaging must be approved by the Associate Administrator prior to being offered for transportation or transported in commerce. a. Mixtures of one or more organic lead mixtures (such as tetraethyl lead, triethylmethyl lead, diethyldimethyl lead, ethyltrimethyl lead, and tetramethyl lead) with one or more halogen compounds (such as ethylene dibromide and ethylene dichloride), hydrocarbon solvents or other equally efficient stabilizers; or. It must be demonstrated that the article relieves its pressure by means of a fire degradable seal or other pressure relief device, in such a way that the pressure receptacle will not fragment and that the article or fragments of the article do not rocket more than 10 meters; and. N73 Packagings consisting of outer wooden or fiberboard boxes with inner glass, metal or other strong containers; metal or fiber drums; kegs or barrels; or strong metal cans are authorized and need not conform to the requirements of part 178 of this subchapter. 11 The hazardous material must be packaged as either a liquid or a solid, as appropriate, depending on its physical form at 55 C (131 F) at atmospheric pressure. 343 A bulk packaging that emits hydrogen sulfide in sufficient concentration that vapors evolved from the sour crude oil can present an inhalation hazard must be marked as specified in 172.327. 430 This entry shall only be used for solid medical waste of Category A transported for disposal. and are not subject to requirements of this subchapter except for the following: (a) Incident reporting. Such packages must be transported on cargo aircraft only. 2 Except when authorized under Special Provision 41. The provisions of this special provision will be effective until January 2, 2023, unless we terminate them earlier or extend them beyond that date by notice of a final rule in the Federal Register. Each tank must be equipped with pressure relief devices conforming to the following requirements: 1 Total venting capacity in standard cubic feet hour (S.C.F.H.) 176 This entry must be used for formaldehyde solutions containing methanol as a stabilizer.